Ürün hakkında
- 400 kV'a kadar Arıza Öncesi Konumlandırma
- 400 kV'ye kadar test
- 70 kV ile VLF
- 50 kV'ye kadar ARM
Standart 110 kV / 290 mA DC testi, 50 kV'a kadar ARM ön konumu ve 2500 J'ye kadar 3 kV ila 50 kV dalgalanması ile R 30 Sistemi, yüksek gerilime kadar alçak gerilim aralığındaki tüm gereksinimleri zorluk çekmeden karşılar.
İsteğe bağlı sistem, 70 kVrms'ye kadar 0.1 Hz kosinüs dikdörtgen test sistemi ve 5 µF @ 0,1 Hz, 15 kV / 25 A ile Yakma ve 80 kV ve 3200 J ile dalgalanan test edilebilir kablo kapasitesi sunar. Daha yüksek voltaj için R 30 sistem isteğe bağlı olarak 400 kV DC ve 400 kV Decay ile donatılabilir.
Tüm çalışma modları, motor tahrikli YG anahtarları aracılığıyla çalışmayı seçen merkezi bir sistem kontrol paneli tarafından kontrol edilir. Tüm Megger ürünleri gibi, R 30 da sistemin çalışması sırasında operatör, kişisel ve ekipman için maksimum güvenlik sağlayan kapsamlı bir güvenlik sistemi içerir.
Ürün belgeleri
Yazılım ve ürün yazılımı
MeggerBook
MeggerBook & MeggerBook Lite
MeggerBook & MeggerBook Lite Software
latest version
What’s new in version 4.4.0
Updates
- Incorrect reset of the propagation speed v/2 on the Settings page
- Incorrect behavior of the Settings page when the virtual keyboard is absent
- Crash when editing report templates
- Preview pages are displayed in letter format
- During an active search, entries that are not visible can be selected
- The cable description in the report does not display any special characters (including ü¼ö¶ä¤)
- In TDR analyses, the velocity is always given in v/2
Improvements
- Database version check
- Refresh on cable changes
- Phase-resolved tanDelta trend data in BA TanDelta MWT
- Improve handling of Winkis data (Sqlite2)
- Save import/export folder path in MeggerBook
- Update TanDelta standards
- Display GPS status on map
- Display the sleeve or cable type when hovering over the cable run
New Features
- Display TE measurements properly in the activity view in MeggerBook
- The radio options on the "Language settings" page are not working well
- Extremely large Megger-mcb files due to PDF reports made manageable
The setup file below is suitable for the installation of both MeggerBook (full version) and MeggerBook Lite (free limited version).
When started with after adding the electronic license key into the installed software, the software starts as MeggerBook full version which allows for easy and comprehensive data evaluation, data archiving, cable management and report creation. A personal quotation for a certain number of licenses can be requested here . The new electronic license key allows for 3 devices to have MeggerBook full version installed on them.
The dongle key licenses from older versions of MeggerBook are not supported with this newer version. Updated electronic license keys can be requested here for previous customers.
Without the required software license key the software starts as MeggerBook Lite which allows for seamless report creation and offers some of the features as the full version while limiting the data storage options as follows:
• Measurements, analyses and reports are not permanently stored in the database
• While cable import and storage are not limited, a maximum of 5 cables can be created using the cable editor of the Lite Edition
At this time, the software can handle the measurement and test data of the following Megger devices:
Test vans: Centrix 2.0, Primeon Centrix City, Compact City, R30 2.0, Variant
Test systems: VLF Sine 34 / 37 / 45 / 62, VLF CR 40/60, TDS 40/60, Easytest 20, MFM 10
TDRs: Teleflex VX(-P), Teleflex SX-1
Note for test systems VLF Sine Wave 45 and VLF Sine Wave 62:
Data of these test systems can only be imported into the software, if the test systems is equipped with firmware version 3.14 or higher. The latest firmware can be found here (VLF Sine Wave 45) and here (VLF Sine Wave 62).
