Sistema de van de teste R30
Sobre o produto
- Pré-localização de falhas de até 400 kV
- Testes de até 400 kV
- VLF com 70 kV
- ARM de até 50 kV
Com seu teste-padrão de 110 kV/290 mA CC, pré-localização ARM de até 50 kV e surtos de 3 kV a 50 kV com até 2500 J, o Sistema de van de teste R30 atende a todos os requisitos de teste, de baixa a alta tensão, sem nenhuma dificuldade.
O sistema oferece um sistema opcional de teste retangular de cosseno de 0,1 Hz de até 70 kV RMS e capacidade de cabo testável de 5 µF a 0,1 Hz, queimando com 15 kV/25 A e oscilando com 80 kV e 3.200 J. Para tensões mais altas, o sistema R30 pode ser opcionalmente equipado com até 400 kV CC e decadência de 400 kV.
Todos os modos operacionais são controlados por um painel de controle central que seleciona o funcionamento por meio de interruptores de alta tensão acionados por motor. Como todos os produtos da Megger, o R30 inclui um extenso sistema de segurança, proporcionando máxima segurança para o operador, bem como para o pessoal e para equipamentos próximos, durante o funcionamento do sistema.
Documentos do produto
Software and firmware updates
MeggerBook
MeggerBook & MeggerBook Lite
MeggerBook & MeggerBook Lite Software
latest version
What’s new in version 4.4.0
Updates
- Incorrect reset of the propagation speed v/2 on the Settings page
- Incorrect behavior of the Settings page when the virtual keyboard is absent
- Crash when editing report templates
- Preview pages are displayed in letter format
- During an active search, entries that are not visible can be selected
- The cable description in the report does not display any special characters (including ü¼ö¶ä¤)
- In TDR analyses, the velocity is always given in v/2
Improvements
- Database version check
- Refresh on cable changes
- Phase-resolved tanDelta trend data in BA TanDelta MWT
- Improve handling of Winkis data (Sqlite2)
- Save import/export folder path in MeggerBook
- Update TanDelta standards
- Display GPS status on map
- Display the sleeve or cable type when hovering over the cable run
New Features
- Display TE measurements properly in the activity view in MeggerBook
- The radio options on the "Language settings" page are not working well
- Extremely large Megger-mcb files due to PDF reports made manageable
The setup file below is suitable for the installation of both MeggerBook (full version) and MeggerBook Lite (free limited version).
When started with after adding the electronic license key into the installed software, the software starts as MeggerBook full version which allows for easy and comprehensive data evaluation, data archiving, cable management and report creation. A personal quotation for a certain number of licenses can be requested here . The new electronic license key allows for 3 devices to have MeggerBook full version installed on them.
The dongle key licenses from older versions of MeggerBook are not supported with this newer version. Updated electronic license keys can be requested here for previous customers.
Without the required software license key the software starts as MeggerBook Lite which allows for seamless report creation and offers some of the features as the full version while limiting the data storage options as follows:
• Measurements, analyses and reports are not permanently stored in the database
• While cable import and storage are not limited, a maximum of 5 cables can be created using the cable editor of the Lite Edition
At this time, the software can handle the measurement and test data of the following Megger devices:
Test vans: Centrix 2.0, Primeon Centrix City, Compact City, R30 2.0, Variant
Test systems: VLF Sine 34 / 37 / 45 / 62, VLF CR 40/60, TDS 40/60, Easytest 20, MFM 10
TDRs: Teleflex VX(-P), Teleflex SX-1
Note for test systems VLF Sine Wave 45 and VLF Sine Wave 62:
Data of these test systems can only be imported into the software, if the test systems is equipped with firmware version 3.14 or higher. The latest firmware can be found here (VLF Sine Wave 45) and here (VLF Sine Wave 62).
